我們?cè)谶M(jìn)行鋁板的裝飾中,很多時分要將其折彎,這完整不是成心的行為,而是工程裝置需求.但是有時分鋁單板會由于折彎過度而這段,以至報廢,發作這種狀況就糜費了一塊鋁單板,因而我們鋁板生產廠家要想方法防止這種情況呈現,那么如何才能防止鋁單板由于折彎而報廢呢?
　　In the process of aluminum plate decoration, we need to bend it a lot of time, which is not intentional behavior, but the demand of engineering devices. But sometimes the aluminum plate will be bent excessively, and even be scrapped, which will cost a piece of aluminum plate. Therefore, we need to find ways to prevent this situation, so how can we prevent the aluminum plate from being scrapped due to bending?
　　1、鋁型材擠壓調直:調直是鋁型材形成彎曲很嚴重的環節,調直工人一定要十分留意調直所用的力度,力氣過大就可能會對型材產生變形、收口、桔皮等,力氣過小就會產生型材調不直,形成彎曲.
　　1. Extrusion straightening of aluminum profile: straightening is a very serious link in the formation of bending of aluminum profile. Straightening workers must pay great attention to the strength used for straightening. If the strength is too large, the profile may be deformed, folded, orange peel, etc., and if the strength is too small, the profile will not be straightened, forming bending

　　2、鋁型材擠壓裝框:這環節也是十分重要,鋸?fù)甓ǔ唛L(zhǎng)度后,鋁單板就要進行裝框,這時裝框工就要留意了:這料是大料還是小料,是帶管料還是平面模拉出來的料?普通來說,大料和帶管的料抬兩端裝框不容易形成彎曲,但小料戰爭面模拉出來的料,抬兩端就很容易形成彎曲,這時就應該從兩端向中間靠攏進行抬料裝框.
　　2. Aluminum profile extrusion and framing: this link is also very important. After sawing the fixed length, the aluminum veneer will be framed. The fashion frame workers should pay attention to whether this material is large material or small material, and whether it is material with tube or drawn by plane die. Generally speaking, it is not easy to form bending when the material with tube is lifted and framed at both ends, but it is easy to form bending when the material with small material is pulled out by plane die, At this time, it is necessary to move from both ends to the middle for loading and framing
　　3、鋁板外表處置上架:坯料經時效,硬度已達標,型材就沒那么容易變彎曲,但上架時還是要留意,兩端抬料時,盡量防止上下鼎力動搖,鼎力動搖也會對已時效的鋁單板形成一定的彎曲。
　　3. Surface treatment of aluminum plate on the shelf: after aging, the hardness of the blank has reached the standard, and the profile is not so easy to bend, but attention should be paid to when putting it on the shelf. When lifting the material at both ends, try to prevent the upper and lower parts from shaking vigorously, which will also form a certain bending on the aged aluminum plate.
　　以上是介紹的鋁板生產廠家防止鋁板折彎時形成損壞的措施，想要了解更多內容，歡迎訪問網站：http://www.ztjywl.com