1.為了減少數控刀片的滑動摩擦材料,需要使用一些乳化油,鋁圓片生產加工,剩余的光滑油不能簡單地擦去,這需要一個特殊的石油劑,泡沫油滲透的常見方法及其self-spraying石油。
　　1. in order to reduce the sliding friction material of NC blade, it is necessary to use some emulsified oil and aluminum wafer to produce and process. The remaining smooth oil can not be simply erased. This requires a special petroleum agent, a common method of foam oil penetration and its self-spraying oil.
　　2.自噴除油除灰:稀釋劑除油劑和除灰劑分別加適量水;2. 調整噴頭角度;3、確保鋁合金型材工藝的自噴時間(多在30秒內);4. 確保鋁晶圓通過循環系統手洗。
　　2. Oil and ash removal by self spraying: add appropriate amount of water to the diluent oil remover and ash remover respectively; 2. Adjust the nozzle angle; 3. Ensure the self spraying time of aluminum alloy profile technology (more than 30 seconds); 4. Ensure that the aluminum wafer is washed by hand through the circulation system.
　　1.使用前加少量飲用水，然后將鋁片滲入池中;(良好的調灰劑);2、參與鋁片脫脂，在5—10秒內自動加熱;3.2~3分鐘去油，用清水沖洗干凈;4、成灰劑成灰(時間不跨越30秒左右);5. 清潔飲用水——晾干(日曬)或停止空氣氧化。
　　1. Add a small amount of drinking water before use, and then infiltrate the aluminum into the pool; (good ash mixing agent); 2. Participate in the degreasing of aluminum, and automatically heat it within 5-10 seconds; 3.2-3 minutes to remove oil, and wash it with clean water; 4. Ash forming agent and ash forming (the time does not exceed about 30 seconds); 5. Clean drinking water - air drying (sun drying) or stop air oxidation.
　　鋁圓片清洗工藝:
　　Aluminum wafer cleaning process:
　　1,用大量冷水清洗污垢的鋁圓片外觀,然后撒水稀釋的清潔劑,用薄布,擦拭鋁圓片的外觀,然后有很多冷水清洗鋁圓片的外觀清潔后,鋁圓片的外觀臟東西沖了。
　　1. First, clean the appearance of the dirty aluminum wafer with a large amount of cold water, then sprinkle water to dilute the detergent, wipe the appearance of the aluminum wafer with a thin cloth, and then clean the appearance of the aluminum wafer with a lot of cold water, and the appearance of the aluminum wafer is dirty.
　　2、檢查鋁盤的外觀，看是否有不干凈的地方，約不干凈的地方整理，知道全部清潔后，再用冷水洗去所有清潔劑。

　　2. Check the appearance of the aluminum plate to see if there is any unclean place. The unclean place should be cleaned first. After knowing all the cleaning, wash all the cleaning agents with cold water.
　　3,除了注意不是安排鋁盤的溫度,由于水的蒸發過快將有害的外觀油漆、洗滌劑的使用期間,必須選擇中性洗滌劑或將侵蝕鋁盤的外觀。
　　3. In addition to not arranging the temperature of the aluminum plate, the neutral detergent must be selected or will corrode the appearance of the aluminum plate during the use of the harmful appearance paint and detergent due to the rapid evaporation of water.
　　以上是鋁板生產廠家為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://www.ztjywl.com
　　The above is the relevant content introduced by the aluminum plate manufacturer for you. To learn more, please visit the website: http://www.jndclyxgs.com